This is such an exciting discovery for me that I cannot wait to show you! I wanted to take the time to make better “after” pieces, but this idea won’t be patient. Seriously!
Back when I was heavy into rubber stamping, I used to make medallions and little elements for books, cards, assemblage (you get the idea) by stamping into hot glue-stick. Let the glue cool down, pull your stamp out and you have a really cool little art piece after you paint all over it.
Run forward a few years and I am now heavily into scale miniatures. I’ve been scouring the internet for architectural elements that I can use to add to my French dollhouse walls, ceilings, pediments, etc. and, BOY! They are kind of expensive if you need a lot of them for your project. Hmmm…. I started to wonder if my glue-stick elements would make good molds for resin pours. After a messy, quick pour, voila! It works! (picture a crazy miniaturist jumping up and down here)
When I buy mixed lots of minis off E-bay there are always a few pieces of broken furniture included. And that’s OK, I can usually use them in some way. This is a junky little bed after super glued a resin piece to the headboard and painted it white. It turned out so cute that I will actually put some legs onto the bed and use it in my shabby chic cottage.
So, here is a run down on the how to’s.
Supplies:
- hot glue gun and glue sticks,
- black permanent ink
- rubber stamps (either clear or rubber, either mounted or unmounted)
- two part resin (get small boxes of two part resin in craft stores)
- a small piece of mat board (to hold your molds)
- paper towels, a small mixing cup and a Popsicle stick
- sandpaper, scissors and a craft knife
- Dremel moto-tool (optional)
Steps:
1. Select rubber stamps that will fit your need. If they are unmounted stamps, you will want to mount them onto something so that you do not burn your fingers while stamping into the hot glue.

2. Use black permanent ink to stamp the image onto a piece of mat board. This is so that you will know where to put the hot glue.
3. Use the glue gun to deposit hot glue onto the stamped image, going over the edges just a bit. My first “mold” had too much glue on it as you will see in the following photos. It isn’t a bad thing, but it looks sloppy and wastes glue.
4. Stamp lightly into the glue just up to the edge of the rubber stamp. Don’t push so hard that the glue gets onto the block or the foam rubber cushion (if you are using that kind of stamp). If you do, the glue will adhere to that part and mess up your stamp.
5. Wait until the glue has cooled down and peel your rubber stamp out of it. Now you have a mold!
6. Mix resin according to manufactures directions. Pour carefully into the glue stick mold. Try not to overflow the mold. If you do, wipe up excess with a paper towel. The more carefully you pour, the less clean up on the resin element you will have to do later.
7. Lightly tap the resin filled mold onto your work surface. This will allow any bubbles to rise to the top. Blow gently onto the resin and the bubbles will pop. This step is very important.
8. Let cure according to manufacturers directions. These little elements usually take only about 10-15 minutes. When solid, peel your resin piece out of the mold.

9. While the resin is still softish, you can use scissors or a knife to whittle away overflow or little sprus. If the piece is too thick, use sandpaper to sand down the back of the piece.

I used super glue to adhere the little element to a junky bed headboard.
When the glue was dry, I got out the Dremel with a sanding bit and cleaned up my resin piece a little more.
A white coat of acrylic paint transformed the bed and her new element. After sanding the whole thing, it began to look very shabby chic. What I thought would be a throw away bed is actually now going to be used in my little cottage.
If you want to see how I made the “rusted” lamp above the bed, click on this link .
I hope that you will find this project useful in ways that apply to your own favorite craft. Happy experimenting!