DIY · Dollhouse miniatures · tutorials

A Nifty Miniature Rocking Horse Made With Ordinary Things

Miniature rocking horse

This little rocking horse took his time being born. I started making him last fall. Stuff happened and stuff happened, as it does, to hinder my mini makes. Now, seven months later, he is finally ready to show you how he was assembled. Continue reading “A Nifty Miniature Rocking Horse Made With Ordinary Things”

DIY · Dollhouse miniatures · tutorials

Coin Cell Battery Holders for Your Scale Miniatures

I’m so over wiring 12 volt wiring. That’s right, I’m over it!. At first I was excited to wire my entire, three story, 1/12 scale miniature house. After completing only one floor of round wire, I am already looking for alternatives.

My grand scheme was to have round wire lighting throughout the entire mini house. It quickly became apparent that I would need to decide where the lights should go before the house was even built, let alone decorated. That was NOT working since I kept changing my mind about what each room would be. So, what to do, what to do? Continue reading “Coin Cell Battery Holders for Your Scale Miniatures”

DIY · Dollhouse miniatures · tutorials

A realistic way to make an “antique” scale miniature rug

To make “antique” rugs, I use iron on transfer paper, BUT let me tell you how to get an aged look that is not so rubbery as you would normally get when you use this stuff. The rugs are so much fun to make that I went a little crazy. Now I just need to build a room box for a rug store. Continue reading “A realistic way to make an “antique” scale miniature rug”

DIY · Dollhouse miniatures · tutorials

Custom Fabrics for a Custom Dollhouse

In regards to dragging my feet on the dollhouse build….LOL…I will freely admit it- I’m a procrastinator. What can I say? But, I’m still busy at all times with SOMETHING.

I’ve been playing around with designing fabrics for my mid-century dollhouse which is ALSO not finished. I just want to make mini accessories at this point, so I’m gonna do what I wanna do. 😅😅😅

This picture shows one design but in a couple different colorways. That is what eats up so much of my time too. I design on the computer (Photoshop) and then change colors over and over and over. Geeze! But color is sooo fun and the computer programs are sooo cool. What’s a girl to do?

I did find out that my ink is not waterproof if I drop something on it right away. See the red arrow where the splotch is? Just wait a couple minutes before you spill your drink on it. (wink, wink) Continue reading “Custom Fabrics for a Custom Dollhouse”

DIY · Dollhouse miniatures · Free Printables · tutorials

Miniature door mat made with a Cricut cutter

Even though I’ve been distracted from working on my dollhouses for quite a while, I continue to make little accessories when time permits. The porch floor is not finished yet, but I couldn’t resist placing this tiny doormat in front of the front door. I designed and made it with a Cricut cutting machine. I think that it looks pretty cute if I may say so myself.

The step-by steps are below if you are interested in making a welcome mat for your own mini door. Actually, even if you don’t have a dollhouse, a mat that is a little larger could make a cute coaster for your coffee cup. Continue reading “Miniature door mat made with a Cricut cutter”

DIY · Dollhouse miniatures · Free Printables · tutorials

Time to make another miniature chandelier!

Are you hooked on rustic French country style? I am too! I just can’t get enough of it, so when a gorgeous antique, wooden French chandelier jumped off the page of my home decor magazine… well,  I just knew that I  had to try to make it. NO! Not full sized, silly.  In 1/12 scale miniature for my little shabby chic cottage.

Antique-French-country-chan
Here is the chandelier taped up to the bedroom ceiling of my old English Tudor cottage just to show you how cute it is when lit. The walls and timbers that you see in the background are not finished yet, so no judging. 😉

The original chandelier in the magazine was made of wood and had a white washed look to it.  I wanted to make my fixture look even more rustic, like wood and old black metal that had been painted white, but has rusted and chipped over time. I think that it shows upscale, chic distress, don’t you?

Continue reading “Time to make another miniature chandelier!”
art · DIY · Dollhouse miniatures

How to make resin elements with glue-stick molds

This is such an exciting discovery for me that I cannot wait to show you! I wanted to take the time to make better “after” pieces, but this idea won’t be patient. Seriously!

Back when I was heavy into rubber stamping, I used to make medallions and little elements for books, cards, assemblage (you get the idea) by stamping into hot glue-stick. Let the glue cool down, pull your stamp out and you have a really cool little art piece after you paint all over it.

rubber-stamps-and-hot-glue-

Run forward a few years and I am now heavily into scale miniatures. I’ve been scouring the internet for architectural elements that I can use to add to my French dollhouse walls, ceilings, pediments, etc. and, BOY! They are kind of expensive if you need a lot of them for your project. Hmmm…. I started to wonder if my glue-stick elements would make good molds for resin pours. After a messy, quick pour, voila! It works! (picture a crazy miniaturist jumping up and down here)headboard-on-miniature-bed

When I buy mixed lots of minis off E-bay there are always a few pieces of broken furniture included. And that’s OK, I can usually use them in some way. This is a junky little bed after super glued a resin piece to the headboard and painted it white. It turned out so cute that I will actually put some legs onto the bed and use it in my shabby chic cottage.

So, here is a run down on the how to’s.

Supplies:

  1. hot glue gun and glue sticks,
  2. black permanent ink
  3. rubber stamps (either clear or rubber, either mounted or unmounted)
  4. two part resin (get small boxes of two part resin in craft stores)
  5. a small piece of mat board (to hold your molds)
  6. paper towels, a small mixing cup and a Popsicle stick
  7. sandpaper, scissors and a craft knife
  8. Dremel moto-tool (optional)

Steps:

1. Select rubber stamps that will fit your need. If they are unmounted stamps, you will want to mount them onto something so that you do not burn your fingers while stamping into the hot glue.

stamps-mounted-on-block
I chose these two stamps because the round one will make a perfect ceiling medallion and the other will be a furniture element. I used a piece of double stick tape to mount the stamp on the right onto a little piece of scrap wood.

2. Use black permanent ink to stamp the image onto a piece of mat board. This is so that you will know where to put the hot glue.

3. Use the glue gun to deposit hot glue onto the stamped image, going over the edges just a bit. My first “mold” had too much glue on it as you will see in the following photos. It isn’t a bad thing, but it looks sloppy and wastes glue.

4. Stamp lightly into the glue just up to the edge of the rubber stamp. Don’t push so hard that the glue gets onto the block or the foam rubber cushion (if you are using that kind of stamp). If you do, the glue will adhere to that part and mess up your stamp.

5. Wait until the glue has cooled down and peel your rubber stamp out of it. Now you have a mold!

6. Mix resin according to manufactures directions. Pour carefully into the glue stick mold. Try not to overflow the mold. If you do, wipe up excess with a paper towel. The more carefully you pour, the less clean up on the resin element you will have to do later.

7. Lightly tap the resin filled mold onto your work surface. This will allow any bubbles to rise to the top. Blow gently onto the resin and the bubbles will pop. This step is very important.

8. Let cure according to manufacturers directions. These little elements usually take only about 10-15 minutes. When solid, peel your resin piece out of the mold.

resin-right-out-of-the-mold
The top two pieces are the glue-stick mold and the bottom two are the resin pieces. You can see in the photo that I overflowed my molds the first time that I poured. If you do this, just wipe up the excess with a paper towel and toss. The nicer you pour, the less cleanup on the resin after it’s out of the mold.

9. While the resin is still softish, you can use scissors or a knife to whittle away overflow or little sprus. If the piece is too thick, use sandpaper to sand down the back of the piece.

scale-resin-elements
You can see that the permanent ink transferred to my little element which was great because I wanted to sand the piece after painting to give it that shabby look. I was glad that there was black underneath. If it did not transfer, I would just paint the piece the color of the wood, let dry and then paint with white to get the dark to show after the sanding.

I used super glue to adhere the little element to a junky bed headboard.miniature-resin-element

When the glue was dry, I got out the Dremel with a sanding bit and cleaned up my resin piece a little more.Dremel-cleanup

A white coat of acrylic paint transformed the bed and her new element. After sanding the whole thing, it began to look very shabby chic. What I thought would be a throw away bed is actually now going to be used in my little cottage.

DIY-shabby-chic-mini-bed

If you want to see how I made the “rusted” lamp above the bed, click on this link .

I hope that you will find this project useful in ways that apply to your own favorite craft. Happy experimenting!

sandy-signature

 

DIY · Dollhouse miniatures

Easy DIY dollhouse lamp

dollhouse-light-pendant

Looking for a cute and easy tutorial on a dollhouse lamp? And shabby chic too? Then you have landed on the right spot! I’m excited to share this 1/12 scale project with you because it was so easy, unique and FAST. Seriously, instant-gratification is my middle name when it comes to crafts. Maybe because every little step takes me so darned long that I get REALLY excited about a project that I can complete in one day.

Below is my step-by-step tutorial on a shabby chic hanging lamp for a 1:12 scale dollhouse. Naturally, it would work in other scales as well. I can totally see it in Barbie’s or Blythe’s house too.

LOL, ignore the dry hands that always have paint caked all over them. (grin)

light-tutorial

  1. The first step was to find something that would be cute in a dollhouse. This pendant is perfect! I got it at Jo-Ann’s fabric store.
  2. Next, I disassembled the pendant.
  3. Then I spray painted the little metal star shape with this kind of rusty looking paint.
  4.  When that was dry I was ready to assemble. In figure 4, you can see my components that I used for the light. I have a 3 volt battery and cell holder with an on-off switch, a 3 volt nano light, several beads, two jump rings and a chain.

Assembly: Thread the beads onto the nano light, insert into the star shape and close up with a jump ring and chain on top. Attach a little drop bead at the bottom of the fixture with a jump ring.  Thread the light wires through the chain and hook up as per manufacturers instructions.

I don’t have my lamp permanently wired yet because I’m not sure if it will go into this kind of modern house with a shabby chic bedroom or into my old English Tudor cottage. The little shabby chic bed is one that I am refurbishing. I often get broken junk in with my Ebay “lot” buys and that’s OK. I can always use parts. The fun thing about this bed is a secret that I will let you in on with the next post. Be sure to come back for the bed tutorial.

You can get the chip battery holders, lights and a whole lot of dollhouse lighting info at True 2 Scale. Check out their little kits too. They are adorable. I especially love the little glitter house kits.

sandy-signature